Zhone 3810Plus Guida Utente

COMSPHERE 3800PlusSERIES MODEMSMODELS 3810Plus and 3811PlusQUICK REFERENCEDocument No. 3980-A2-GL10-10

8Diagnostic Control PanelThe Diagnostic Control Panel (DCP) is the user interface to the modem. It provides a2-line, 32-character liquid crystal disp

9Checking the SDCPIf an SDCP is installed, verify that the SDCP can be used to control the 3811Plusmodem. Perform the following steps.SelectSDU1 2 3

103800Plus Modems Menu TreeCall_Setup Status Test“Status”DialDisconnectAnswerDial_StandbyorReturn_to_DialChange_DirectoryDirectory Locations 1 – 10Ab

11ConfigureLd EditArea frm:Edit SaveChoose FunctionActive (Saved) Customer1 Customer2V42/MNP/BufferErr Contrl ModeSync Comp ModeSDC NegotiationSDC Id

12Control RemoteSpeakerResetMake_BusyorRemoveMakeBusyService_LineorDiscServLineDownload CodeSecondary Prim (data blckd)(ExitRem appearsinstead of Rem

13Configuration Option Procedures — DCP Commands1. Move to the Configure branch and select a configuration area to load from: Active(Operating), Act

14Configuration Option Procedures — AT CommandsLoading Factory ConfigurationsUse the AT&Fy&Wn command to load a factory configuration to eith

15AT COMMANDSBold text indicates Async Dial factory defaults.AT Attention Command Prefix/AutobaudRate. Indicates a command string hasstarted and dete

16AT COMMANDS (continued)Yn Long Space DisconnectY0 Disable.Y1 Enable.Zn Reset and Load ActiveZ0 Loads contents of Active (Saved) intoActive (Operati

17AT COMMANDS (continued)&M232, &Q232 Modem operates in Async mode;V.25bis Async dialing is enabled.&M233, &Q233 Modem operates i

Copyright E 2002 Paradyne Corporation.All rights reserved.Printed in U.S.A.NoticeThis publication is protected by federal copyright law. No part of th

18AT COMMANDS (continued)\Dn CTS Control\D0 Forced On. CTS is forced ON.\D1 Standard RS232 operation.\D2 Wink When Disc. CTS turns Off forapproximate

19RESULT CODESNumbers(1) Numbers(2) Words 0 0 OK 1 1 CONNECT 2 2 RING 3 3 NO CARRIER 4 4 ERRORResult Codes 5–14, 16, 19 ar

20S-REGISTERSRegister Description Factory Setting Range S0 Auto-Answer Ring Number 1 0(Disable) or 1–255 rings S2 AT Escape Character 43(+) 0–127 A

21S-REGISTERS (continued)Register Description Factory Setting RangeS43 Train Time 0 0=Long; 1=ShortS44 Leased-Line Rate 27 1=14400(V.32bis); 2=12000(

22S-REGISTERS (continued)Register Description Factory Setting RangeS77 DTR Alarm Reporting 0 0=Disable; 1=EnableS78 Dial Automode 0 0=Enable; 1=Disab

23Important Safety Instructions1. Read and follow all warning notices and instructions marked on the product orincluded in the manual.2. Slots and op

24Notices!WARNING:THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITSFOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULE

253. The Ringer Equivalence (REN) is used to determine the quantity of devices whichmay be connected to the telephone line. Excessive RENs on the tel

2610. An FCC compliant telephone cord with modular plugs may be provided with thisequipment. This equipment is designed to be connected to the teleph

1COMSPHERE 3800Plus Series ModemsModels 3810Plus and 3811PlusQuick ReferenceDocument Number 3980-A2-GL10-10February 2002Product Documentation on the

2Model 3810Plus InstallationDTE ConnectionUse the following procedure to connect the RS-232D cable from the modem to theDTE:1. Make sure the modem’s

3Dial-Line ConnectionUse the following procedure to connect the 3810Plus modem to the dial networkinterface:1. Insert the 6-position, 4-conductor mod

4Network Management System ConnectionFor the 3810Plus modem, use the following procedure to connect the modem to thenetwork management system interfa

5Model 3811Plus InstallationThe COMSPHERE 3000 Series Carrier has 17 slots which can hold up to 16 modemsand one SDU. The SDU is required when the mo

6495-147972. At the front of the carrier, hold the modem vertically, with the latch on its faceplatein the open position, and insert it into the top

7CircuitCardGuidesCircuitPackLockLatchOpen(Unlocked)Closed(Locked)495-148134. If the carrier is connected to power, the Power LED on the faceplate of